Control Panel Modifications
IMPORTANT Placement of joysticks must be horizontal to the control panel for proper playing capability. Use template 16-10151 from kit, as a guide. 1. Remove control panel buttons, joysticks and old control panel artwork. 2. Use the full control panel template to design the control panel. Separate templates are located on the last pages of this manual. 3. Plug previous holes with wood blocks, putty, cardboard or epoxy. Drill new holes as needed for joysticks and control panel buttons. File new...
Table Of Contents 1
CONTROL GRIP BOARD - COMPONENT LAYOUT 50 CONTROL GRIP BOARD-SCHEMATIC 51 DISPLAY BOARD-COMPONENT LAYOUT 52 AUDIO AMPLIFIER BOARD - COMPONENT LAYOUT 54 AUDIO AMPLIFIER BOARD-SCHEMATIC 55 RAM BOARD - COMPONENT LAYOUT 56 CPU BOARD - COMPONENT LAYOUT 58 PATTERN TRANSFER BOARD - COMPONENT LAYOUT 60 PATTERN TRANSFER BOARD - SCHEMATIC 61 ROM RAM BOARD DOMESTIC - COMPONENT LAYOUT 62 ROM RAM BOARD DOMESTIC - SCHEMATIC 63 ROM RAM BOARD FOREIGN - COMPONENT LAYOUT 64 ROM RAM BOARD FOREIGN - SCHEMATIC 65...
Caution
Handle Disk Drive Unit With Care. Use special care when installing the circuit boards and handling the hard disk drive. Take basic precautions to avoid excessive impact or electrostatic discharges. Attached to the hard disk drive is a shock indicator that detects severe impacts. Do not remove or tamper with this indicator. Thoroughly review the operator's manual and videotape provided with this product. Properly Attach All Connectors. Make sure that the connectors on each printed circuit board...
Sectio
The following safety instructions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page before preparing your game for play. AC POWER CONNECTION. Before connecting the game lo the AC power source, verify that the line voltage selection chart jumper wires are installed correctly for the line voltage in your area. For details, refer to Section 3. PROPERLY GROUND THE GAME. To...
TABLE OF CONTENTS contd
VI. Technical Introduction General Harness Component Transformer and Line Voltage A Glossary of Microprocessor Introduction to the Z80 General Purpose Registers Arithmetic and Logic Unit Instruction Register and CPU Z80 CPU Pin VII. Coin Door Maintenance Metal Coin Acceptor Plastic Coin Acceptor Introduction Symptom Guide to Schematic Theory of Differences Between Controls You May Not Touch Parts Wells Gardner Monitor Schematic Wells Gardner Monitor Replacement Parts List Electrohome Monitor...
1 Handling Precautions
When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine. Before performing work, be sure to turn power off. Performing the work without turning power off can cause an electric shock or short circuit. In the case work should be...
Playing the Game
Escape takes place on the surface of a futuristic, imaginary industrial planetoid called Planet X. The humans stationed on Planet X have been enslaved and forced to create a robot empire destined to attack earth. The two heroes, Jake and Duke, must find their way through multiple levels of robot factories and the maze of the canal zones in search of Professor Sarah Bellum a voluptuous young lady famous for her knowledge of cybernetics , freeing other human hostages along the way. Players...
Hold Key To Bypass Selftest
Figure 2-1 Program ROM and RAM Test Screen The top of the screen shows the ROM test result. The numbers on the left and the letters on the top of die screen show the locations of the ROMs on the main PCB. If a white box appears, then the ROM there is good. If an empty box appears as shown at 200U and 210U , then the ROM there is bad. If notiiing appears, then nothing was tested there. The RAMs are tested after the ROMs. If the RAMs have no errors, then you see the message Program RAM OK Jf the...
Figure 21 Program ROM and RAM Test Screen
The top of the screen shows the ROM test result. The numbers on the left and the letters at the top of the screen show the locations of the ROMs on the main PCB. If a white box appears, then the ROM at that location is good. If an empty box appears as shown at 200U and 210U , then the ROM there is bad. If nothing appears, then nothing was tested there. The RAMs are tested after the ROMs. If the RAMs have no errors, then you see the message Program. RAM OK. If the test finds an error, then you...
Portable Appliance Testing
During testing of the machine with a portable appliance tester the insulation test will show a failure due to the fitting of two VDRs between live earth and neutral earth. These components have been fitted to safeguard against high voltage surges that may occur on the mains supply to the machine and to comply with the EMC regulations. To conduct an insulation test on this machine, the VDRs must be isolated from the circuit first. Ensure that the VDRs are reconnected after the insulation test...
Moving The Machine
This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface. j The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly. The fitting position of the Header Assembly is high, and it is important that a means of reaching the height safely,without stretching, is available. e.g. Steps, Step Stool etc. j The overall height of the machine, with the Header...
Transformer EMI Assembly 8000190
PART NO. 530-0016 250-0460 250-0461 800-0170 253-0206 482-0104 313-0023 313-0014 313-0015 482-0100 482-0019 420-0557 PCB Assembly PCB Support, Threaded Thread Forming Screw, 6, Type B, 3 8 long Power Transistor Audio Amp TIP 125 Power Transistor Audio Amp TIP 120 Nylon Transistor Insulator Mica Transistor Insulator Flat Washer, 4 Lock Split Washer, k G-80 POWER SUPPLY CHASSIS ASSEMBLY-Continued ITEM NO. PART NO. QTY REQD. G-80 Power Supply Chassis Assembly 800-0191 ITEM NO. PART NO. QTY REQD....
Order By Part Number Only
8 x 3 4 SLT. HEX HD. WD. SCR. 4 REQ'D. 5-5 8 SQ. VENT GRILL 2 REQ'D. ELECTROHOME -19 COLOR MONITOR W CHASSIS, WELLS-GARDNER -19 COLOR MONITOR 1 4-20 x 1-1 4 UNSLOTTED FIN. HEX HD. P.C. SUPPORT BRKT. -12 2 REQ'D. P.C. SUPPORT BRKT. - 6-1 2 2 REQ'D. 8x3 4 SLT. HEX HD. SCREW 10 REQ'D. 8-32 x 3 4 CARRIAGE BOLT 4 REQ'D.
Color Xy Monitor And G80 Circuit Description
To begin our discussion of the Color X-Y Monitor, let's first pay tribute to the other kind of monitor - the raster-scan. As you may remember from your knowledge of raster-scan displays like those in a TV , that the electron-beam inside the tube always moves in a predictable way. That is, it always starts at the top left of the screen and scans across it, forming a pattern of horizontal lines on the inside surface of the tube as it moves downward. When it gets to the bottom, the beam is forced...
Punkter Om Installation
Tand aldrig for strammen til maskinen for installering er fuldfort. For at undga mulige elektriske st0d sikres, at maskinen er forbundet til hovedstrammen med sikkert monterede jordstik. For at kunder ikke kommer til skade ved spillets bevagelser sikres, at der er mindst 50cm afstand til andre maskiner og vagge. For at undga skader pa maskinen p.g.a. fejlbetjening sikres, at sp ndingen pa hovedstrommen er 230 volt AC. BEMERK Hvis denne maskine placeres pa et poleret gulv, anbefales det at ligge...
Order By Part Number Only 1
UPPER DISPLAY PLEXI -17-15 16 x 5-3 4 x 3 16 194 WEDGE BASE LAMP 14V., 27A 5 REQ'D. 8 x 5 8 PHIL. TRS. HD. SCR. 3 REQ'D. TOP, 3 REQ'D. BOTTOM BLACK SPEAKER GRILL W 4-1-1 2 SCREWS 6 x 9 SPEAKER ASSY. W CABLE, 8 OHM, 7W. 8-32x 1-1 2 CARRIAGE BOLT 4 REQ'D. MAIN GLASS ASSY. -17-13 16 x 13-1 8 x 3 16 13 COLOR MONITOR DUALSYNC HORIZONTAL MTG. - ELECTROHOME GLASS CHANNEL-14-1 2 LG. 2 REQ'D. 8-32 x 1-1 4 CARRIAGE BOLT 3 REQ'D. SMALL RED SWITCH BUTTON W HARDWARE 2 REQ'D. 8-32 x 1-1 8 CARRIAGE BOLT 6...
Inspections Immediately After Transporting The Product To The Location
Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects cuts, etc. on the external surfaces of the cabinet Are Casters and Adjusters, damaged Do the power supply voltage and frequency...
Warning
If a fluorescent tube drops and it breaks, it will implode Use care in handling. Switch OFF power to the game. Remove the marquee glass. Disconnect the fluorescent light assembly from its power cable. Remove the screws fastening the assembly to the cabinet and lift out the assembly. Switch OFF power to the game. Remove the steel speaker screen. Remove the baffle, taking care not to damage the speaker enclosure seals. The speakers pull out from the front of the cabinet. Be sure to disconnect the...
Kit Components
Unpack materials from carton and inspect for obvious signs of damage. Use this checklist to ensure the kit is complete. Some of these parts may already be installed. You must supply the remainder of the materials required for this conversion. Unpack materials from carton and inspect for obvious signs of damage. Use this checklist to ensure the kit is complete. Some of these parts may already be installed. You must supply the remainder of the materials required for this conversion.
midway games west inc 675 sycamore drive milpitas California 95035 httpwww
20-9620 4006-01003-04 4106-01001-10 4108-01193 1 OB 4308-01123-24B 4408-01128-00 4700-00012-00 5556-13956-00 5556-15272-00 KEY T20 TR-TX LONG ARM MS 6-32x1 4 P-PH-SEMS 4 SMS 6x5 8 P-PH 4 SMS 8x5 8 TRX 10 BLT 8-32x1-1 2 CB 16 NUT 8-32 KEPS 17 FW .172x.375x.036 17 FERRITE BEAD 2PC 1-1 4 SQ 3 FERRITE BEAD .375 IN. ID. 1 08-8067 CARDBOARD BEZEL BLACK UNIV 31-3581 SIGN P.O.P. DARK LEGACY 03-9663 SHIELD-ATTRACTION GAMES WEST REGISTRATION CARD MANUAL UNIV KIT LABEL FBI WARNING LABEL- EPILEPSY TEMPLATE...
TwoPlayer Game
Players battle each other in a match decided by winning two out of three rounds. A trophy and human followers are awarded to the player who wins each round, and a new territory on the globe is awarded to the winner of the match. Human followers are awarded for various accomplishments in the game. The number of followers awarded depends upon how well a player fights, including at tack combinations, damage to the opponent, use of finishing moves, and fatalities. If the two players are tied at the...
Order By Part Number Only
ACRYLIC HEADER - 22-3 8 x 7-7 16 x 3 16 GLASS CHANNEL-7-1 2 LG. 2 REQ'D. TOP HEADER BRKT. - 22-13 16 LG. BOTTOM HEADER BRKT. - 22-13 16 LG. 8x 5 8 PHIL. TRS. HD. S.M.S. 6 REQ'D. 8-32x 3 4 SLT. PAN HD. M.S. 4 REQ'D. REAR SCENERY BRKT. -8-3 8 LG. 2 REQ'D. 8 x 5 8 SLT. HEX HD. S.M.S. 8 REQ'D. DECORATIVE SIDE PANEL- RIGHT NOT SHOWN 22-5 16 x 20-7 8 x 1 8 GLASS EDGE CHANNEL-19-7 8 LG. 2 REQ'D. WEDGE BASE LAMP SOCKET 1532 6 REQ'JD. 8-32x 1-1 2 CARRIAGE BOLT 2 REQ'D. 8-32 x 1-1 16 CARRIAGE BOLT 6...
60 Color Service Generator for G07 Monitor
Electrohome has developed a color service generator that is specifically designed for use with the G07 color data monitor. It provides the monitor with both horizontal and vertical sync, as well as the following test patterns 2 Broad bar cross-hatch pattern Three color selection switches, red, green and blue, provide the ability to display the above patterns in the three primary colors as well as the three secondary colors. This product may be ordered from Contracts Marketing ELECTROHOME...
Cable Block Diagram
4. Open the player control panel and locate player panel cable H-22785. This cable connects to the joysticks, switches, fuses, and I-40 adapter. Connectors designated Player 1 mostly white wire colors and Player 2 violet mate with the same color cables from the main harness. Player 3 blue and Player 4 gray connectors mate with the same color cables from the main harness. Power connectors red and black from player panel fuses mate with the same color cable from the main harness. 5. Check wiring...
Table of Contents
1. Voltage Plug 2. Interlock and Power On Off D. Self-Test E. Option Switch 2. Coin Mechanism Multipliers 9 3. Examples of Game Price Settings 9 1. Attract 2. Ready-to-Play Mode 3. Play Mode 4. High Score initial Mode B. Fuse C. The Control Panel 1. LED Start-Switch 2. Leaf-Switch 3. Mini-Trak Ball Maintenance and Repair 19 D. Monitor E. Printed-Circuit Board 1. Game PCB 2. Regulator Audio II PCB F. Fluorescent Tube and Speaker Replacement 23 G. Game Illustrations and parts lists begin on page...
5 Accessories
When transporting the machine, make sure that the following parts are supplied. If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you. The Keys are inside the Coin Chute Door at the time of shipment from the factory. GD-ROM SERVICE MANUAL ENG 420-6620-01 1 INSTRUCTION MANUAL FOR THE GAME BOARD AND GD-ROM The Keys are...
Tools Required
Drill with a 1 2-inch and 5 l6-inch drill bits Socket wrench set and ratchet Color RGB monitor ' Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency 15.750 KHz Vertical frequency 60 Hz Video input IV to 3V peak-to-peak positive polarity 5 VDC 0.25V U 3.0 amps ' 12 VDC 1.0 amp -5 VDC 1.0 amp optional Insulated wire connectors if you are installing a new JAMMA harness 6 x l 2-Long, Type AB, Pan-Head, Snap-Action Switches 8 ji 10-24 x...
Function Labels Overlay Installation
Line up the supplied function labels with the corresponding control panel holes. Remove the backing and carefully press into place. Be sure they are straight. Attach the HOOK SWING reference diagram above the trackball label. If your control panel is too narrow to fit the reference diagram, mount the diagram under the monitor glass on the bezel. Refer to the diagrams below. face left face right overlay overlay FUNCTION LABEL LAYOUT 1 NOTE TRACKBALL SHOULD BE CENTERED ON THE CONTROL PANEL...
Introduction Of The Owners Manual
SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSIs, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative arid popular game machines to the world market. This Owner's Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation o electronic assemblies, eiectromechanicals, servicing control, spare parts, etc. as regards TITLE FIGHT, a new SEGA...
Safety Summary
The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply. Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should be only be plugged into a grounded three-wire outlet. If you have only a two-wire outlet, we recommend you hire...
How to Use this Manual
This manual, written for game operators and service technicians, describes the Pole Position game. The manual contains information about the Upright and Sit-Down Pole Position cabinets. Whenever information is unique to the Upright cabinet, this symbol appears Whenever information is unique to the Sit-Down cabinet, this symbol appears Wherever information is unique to Ireland-Built games, this symbol appears _ Chapter 1 describes new features, game setup, settings of option switches, self-test...
Product specifications
Medium Resolution RGB or Standard Resolution RGB adjustable at U12 DIP switches Player Variables 1 to 4 Players Per Game Choice of Character Character Profile Memory Operator Variables Coinage, Game Options, Difficulty, Volume, Demo Mode, Audits, Statistics Automatic Power-Up Test Manual Multi-Level Menu System
Regulatoraudio Pcb Schema
The Regulator Audio PCB has the dual functions of regulating the 5 VDC logic power to the game PCB and amplifying the audio from the game PCB. The regulator consists of voltage regulator Q1, current source power transistor Q3 and Q3's bias transistor Q2. The regulator accurately regulates the logic power input to the game PCB by monitoring the voltage through high impedance inputs SENSE and -SENSE. The inputs are directly from the 5 VDC and ground inputs to the game PCB. Therefore, the...
Warning 1
To avoid possible electrical shock, turn off and unplug the game before performing any maintenance procedures. Perform the following procedure to remove replace the 1. Use a 1 8-inch hex driver to loosen the two screws securing the lower retainer to the cabinet. 2. Unlock and open the coin door on the front of the cabinet. 3. Carefully reach up through the coin door opening and release the spring-draw latches located under the control panel on both sides of the cabinet. 4. Use a 1 8-inch hex...
Installing the Foot Pedal
To install the foot pedal, you need a copy of the foot pedal installation template printed at the end of this chapter and the following parts from the kit Four fender washers and locknuts 1. Tape the foot pedal template to the lower right corner on the front of the game. Make sure the template is placed correctly as per the measurements printed on it. 2. Drill four 5 l6-inch corner holes and a 1 3 16-inch center hole through the template. 3. Feed the pedal harness through the large, 1 3 16-inch...
5 Accessories
When transporting the machine, make sure that the following parts are supplied. Magnetic cards for the recording of play results, and cleaning kits for cleaning the head of the card reader writer are sold separately. Subsequent purchases of these items can be made by contacting the office listed on this Owner's Manual or the dealer from whom the product was originally purchased. Be sure to provide the part number s , name s , and required number of items. 601-11050 CLEANING CARD Package of 30...
Precautions Concerning The Place Of Installation
This is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage o Places subject to rain or water leakage, or condensation due to humidity, o In the proximity of an indoor swimming pool and or shower, o Places subject to direct sunlight. o Places subject to heat sources from heating units, etc., or hot air. o Vicinity of highly flammable volatile chemicals or hazardous matter, o Vicinity of anti-disaster...
Connecting Power Wires
1. Connect the wires on the JAMMA harness to the wires for the power supply. You need 5V, -5V, and 12V for the Escape kit. This kit may not require all of the voltages used in your original game. Tie off any unused wires on the power supply. 2. You will notice that there is more than one wire for each voltage. You must use more than one wire, as called out in the footnotes of Table 1-2. Using more than one wire for each voltage ensures that you do not overload the edge connector and cause it to...
7 Precautions To Be Heeded When Moving The Machine
0 When moving the machine, be sure to unplug the power plug. Moving the machine with the plug as is inserted can damage the power cord, and cause fire and electric shock hazards. 0 When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords and earth wires. Damaging the power cords can cause electric shock and short circuit hazards. 0 When moving the...
2 Care In Operation
o Are the IC boards and other connectors firmly connected oConnect ground wire as prescribed. Never connect to gas pipes, water pipes or electrical conduits o Arrange line cords and ground wires in the aisle so they will not be tripped over. o Always turn off the power supply switch before handling. o Avoid inserting and pulling the plug in rapid succession. oDo not check the IC board circuit with a tester. oCare should be taken t.o avoid dragging or dropping the machine when transporting it,...
Selftest
Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the game's speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and or service man to have the trouble fixed unless it is something you can do yourself such as replace a bad RAM or...
Warning
To avoid electrical shock, unplug the cabinet while installing the kit. After installation. plug the game only into a grounded 3-wire outlet. Glass fieiainsr i 1782 148011 8 Foam Taoe 0479944 21 Bezel w ti Graphics i 178056-002.-t 2 W. x V16 I Thk Foam Tape i A0479824 Trak-8ail Adapter Harness Assy. 75-07002 F lai washer 75-99515 1 4 gt 20 NuV Washer Assy. A047441-01 JAMMA Powet J Supply Assy. 3A. 2S0V Fuss I A047365-01 SilUUZ PCS Assy, j 178265-001 t.-StyieNytonStarxloft 75-51488 i 10x3.0-...
Game Pcb 1
Table 1-1 details game option switch settings on the game PCB. Options are preset at the factory and shown by the symbols. However, you may change the settings to suit your individual needs. To verify option switch settings, push reset button or power the game off and then on again. Set the self-test switch to on and verify the settings on the self-test screen. Then set the self-test switch to off. This table contains switch settings for options relating to game price, number of Fast Freddie...
C Z80 Control Logic
This section describes the generation of three control inputs to the Z80 CLOCK , RESET-, and WAIT-. The control input Bus Request BUSRQ- may be wired on some boards, but it is never used. The Clock Circuit provides the Z80 Controller Board with a stable source of timing, thus insuring, among other things, that all audio sounds remain in tune. Composed of U24, U29, Yl, and other discrete parts, the Clock Circuit consists of an oscillator and several dividers and drivers. The oscillator is...
Rear View
ITEM NO. PART NO. QTY. REQ'D DESCRIPTION REF. DESG. Junction Box Metal Conn Quick Fem Fully .250 X .032 AWG 18-22 Conn Quick Fem Fully .187 X .020 AWG 18-22 Decal 2 Amp Fuse Switch SPDT Cherry Fuse 2 AMP 250V S.B. Holder Fuse Cord Line 3 Cond. ITEM NO. PART NO. QTY. REQ'D DESCRIPTION REF. DESG. 24 284-0007 1 Washer Flat Std O.D. l 4 25 283-0025 1 Nut Hex HD 10-24 Mach 26 282-0005 1 Bolt Carriage 10-24 27 310-0016 1 Insul TBG .187 ID 28 284-0004 2 Washer Flat Std O.D. 8 Button Plunger Yellow...
List of Illustrations
Figure 3 International Voltage Plug Selection 4 Figure 4 Interlock and Power On Off Switches 5 Figure 6 Location of Self-Test Switch, Volume Control and Option Switches 7 Figure 8 Game Option Figure 9 Game Price Figure 10 Coin Counter Option Figure 11 Opening the Control Panel and Replacing Switches 20 Figure 12 Control Panel Wiring Figure 13 Encoder Wheel Maintenance and Repair 22 Figure 14 Video Display Figure 15 Printed-Circuit Board Removal 25 Figure 16 Speaker and Fan Figure 17 Power...
Aztarac Table Of Contents
I. GENERAL INFORMATION PAGE NO. User Information Introduction Game Description Game Diagnostics Game Optional Switch Settings Installation amp Electrical Requirements ------------------------------14 110 220 VAC Conversion 110 220 VAC Interconnect Diagram 904-0006 Fig.l --------16 Routine Maintenace amp Service- Power Supply ----------------------17 Power Supply PSR-1105AP Troubleshooting Guide 18 Display PCB X-Y Monitor Adjustment Procedure 19 III. GAME PARTS DRAWINGS- PARTS LIST amp...
Starting Up
Switch on power to the game. A rug pattern appears on the CRT screen. When the rug pattern ends, the screen shows CHECKING SCRATCH RAMS, and then CHECKING ROMS. The next screen shows SUPER HIGH IMPACT FOOTBALL REVISION LEVEL, CMOS TEST OK and the COIN SETTING. The game then moves to the Attract Mode. Insert the desired amount of coins or tokens. Select which player receives the credit by pressing the appropriate Player Start Button. Continue pressing the Player Start button until all credits...
2 Specifications
Connected to JAMMA standard terminal 5V 5 2.5A or more and 12V 5 2.0A or more Temperature 0 C - 50 C, Humidity 10 - 85 no condensation Cabinets corresponding to JAMMA standard Direction of the monitor and the monitor signal Type of scanning retrace line Switchable to non-interlace interlace Horizontal synchronizing frequency 15.75kHz Vertical synchronizing frequency 60.0Hz 4-direction joystick 1x2 Button switch 1 x 2 Startswitch 1x2 Fix to the wooden install board of the cabinet 1 JAMMA...
To mount trackball to a wooden control panel without routing capability use
1. Fill any existing holes in the wooden control panel. 2. Place and secure Template 3 to your control panel in the desired location. NOTE The trackball should be as far away from the monitor as possible. 3. Carefully cut the hole for the trackball in the shape indicated on the template. The trackball should fit the hole shape exactly. 4. Drill the mounting holes as indicated. 5. Remove template and file down any rough edges. 6. Using the Trackball Orientation Template, cut a 3 hole in the...