Arcade Machine Games

Control Panel Modifications NBAHangtime

Fri, 18 May 2012 02:27:12 GMT

IMPORTANT Placement of joysticks must be horizontal to the control panel for proper playing capability. Use template 16-10151 from kit, as a guide. 1. Remove control panel buttons, joysticks and old control panel artwork. 2. Use the full control panel template to design the control panel. Separate templates are located on the last pages of this manual. 3. Plug previous holes with wood blocks, putty, cardboard or epoxy. Drill new holes as needed for joysticks and control panel buttons. File new...

Table Of Contents 1 Gorf

Wed, 16 May 2012 20:16:21 GMT

CONTROL GRIP BOARD - COMPONENT LAYOUT 50 CONTROL GRIP BOARD-SCHEMATIC 51 DISPLAY BOARD-COMPONENT LAYOUT 52 AUDIO AMPLIFIER BOARD - COMPONENT LAYOUT 54 AUDIO AMPLIFIER BOARD-SCHEMATIC 55 RAM BOARD - COMPONENT LAYOUT 56 CPU BOARD - COMPONENT LAYOUT 58 PATTERN TRANSFER BOARD - COMPONENT LAYOUT 60 PATTERN TRANSFER BOARD - SCHEMATIC 61 ROM RAM BOARD DOMESTIC - COMPONENT LAYOUT 62 ROM RAM BOARD DOMESTIC - SCHEMATIC 63 ROM RAM BOARD FOREIGN - COMPONENT LAYOUT 64 ROM RAM BOARD FOREIGN - SCHEMATIC 65...

Caution Area51

Sat, 12 May 2012 14:47:00 GMT

Handle Disk Drive Unit With Care. Use special care when installing the circuit boards and handling the hard disk drive. Take basic precautions to avoid excessive impact or electrostatic discharges. Attached to the hard disk drive is a shock indicator that detects severe impacts. Do not remove or tamper with this indicator. Thoroughly review the operator's manual and videotape provided with this product. Properly Attach All Connectors. Make sure that the connectors on each printed circuit board...

Sectio Mortal Kombat 2

Fri, 11 May 2012 20:49:36 GMT

The following safety instructions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page before preparing your game for play. AC POWER CONNECTION. Before connecting the game lo the AC power source, verify that the line voltage selection chart jumper wires are installed correctly for the line voltage in your area. For details, refer to Section 3. PROPERLY GROUND THE GAME. To...

TABLE OF CONTENTS contd BurgerTime

Thu, 10 May 2012 21:42:32 GMT

VI. Technical Introduction General Harness Component Transformer and Line Voltage A Glossary of Microprocessor Introduction to the Z80 General Purpose Registers Arithmetic and Logic Unit Instruction Register and CPU Z80 CPU Pin VII. Coin Door Maintenance Metal Coin Acceptor Plastic Coin Acceptor Introduction Symptom Guide to Schematic Theory of Differences Between Controls You May Not Touch Parts Wells Gardner Monitor Schematic Wells Gardner Monitor Replacement Parts List Electrohome Monitor...

1 Handling Precautions Hotd3

Mon, 07 May 2012 09:56:56 GMT

When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine. Before performing work, be sure to turn power off. Performing the work without turning power off can cause an electric shock or short circuit. In the case work should be...

Playing the Game AtariGames

Mon, 07 May 2012 02:40:07 GMT

Escape takes place on the surface of a futuristic, imaginary industrial planetoid called Planet X. The humans stationed on Planet X have been enslaved and forced to create a robot empire destined to attack earth. The two heroes, Jake and Duke, must find their way through multiple levels of robot factories and the maze of the canal zones in search of Professor Sarah Bellum a voluptuous young lady famous for her knowledge of cybernetics , freeing other human hostages along the way. Players...

Info Fcn Pacman 2

Tue, 01 May 2012 08:08:04 GMT

VOKC CLAMP SCREW FRON PyfiMr MAGNETS POLE CONVERGENCE MAGnE'S BEAR -POLE CONVERGENCE MAGNETS KINO RING ON 2 INCH MODELS 2.0 Static and Dynamic Convergence NOTE Static convergence is achieved by four magnets located on the neck, nearest the base of the picture tube, Fig. 2. The middle pair of magnetic rings are adjusted to converge the blue and red crosshatch lines. The.rear pair of convergence rings closest to the base of the picture tube are adjusted to converge the magenta blue red to the...

Hold Key To Bypass Selftest Racedriv

Sat, 28 Apr 2012 17:49:55 GMT

Figure 2-1 Program ROM and RAM Test Screen The top of the screen shows the ROM test result. The numbers on the left and the letters on the top of die screen show the locations of the ROMs on the main PCB. If a white box appears, then the ROM there is good. If an empty box appears as shown at 200U and 210U , then the ROM there is bad. If notiiing appears, then nothing was tested there. The RAMs are tested after the ROMs. If the RAMs have no errors, then you see the message Program RAM OK Jf the...

Figure 21 Program ROM and RAM Test Screen StunRunner

Sat, 28 Apr 2012 17:49:45 GMT

The top of the screen shows the ROM test result. The numbers on the left and the letters at the top of the screen show the locations of the ROMs on the main PCB. If a white box appears, then the ROM at that location is good. If an empty box appears as shown at 200U and 210U , then the ROM there is bad. If nothing appears, then nothing was tested there. The RAMs are tested after the ROMs. If the RAMs have no errors, then you see the message Program. RAM OK. If the test finds an error, then you...

Portable Appliance Testing TokyoWars

Fri, 27 Apr 2012 00:56:18 GMT

During testing of the machine with a portable appliance tester the insulation test will show a failure due to the fitting of two VDRs between live earth and neutral earth. These components have been fitted to safeguard against high voltage surges that may occur on the mains supply to the machine and to comply with the EMC regulations. To conduct an insulation test on this machine, the VDRs must be isolated from the circuit first. Ensure that the VDRs are reconnected after the insulation test...

Moving The Machine Alpine Racer 2

Thu, 26 Apr 2012 02:54:56 GMT

This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface. j The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly. The fitting position of the Header Assembly is high, and it is important that a means of reaching the height safely,without stretching, is available. e.g. Steps, Step Stool etc. j The overall height of the machine, with the Header...

Transformer EMI Assembly 8000190 Eliminator

Tue, 17 Apr 2012 16:52:22 GMT

PART NO. 530-0016 250-0460 250-0461 800-0170 253-0206 482-0104 313-0023 313-0014 313-0015 482-0100 482-0019 420-0557 PCB Assembly PCB Support, Threaded Thread Forming Screw, 6, Type B, 3 8 long Power Transistor Audio Amp TIP 125 Power Transistor Audio Amp TIP 120 Nylon Transistor Insulator Mica Transistor Insulator Flat Washer, 4 Lock Split Washer, k G-80 POWER SUPPLY CHASSIS ASSEMBLY-Continued ITEM NO. PART NO. QTY REQD. G-80 Power Supply Chassis Assembly 800-0191 ITEM NO. PART NO. QTY REQD....

Order By Part Number Only Rallyx

Sat, 14 Apr 2012 16:49:35 GMT

8 x 3 4 SLT. HEX HD. WD. SCR. 4 REQ'D. 5-5 8 SQ. VENT GRILL 2 REQ'D. ELECTROHOME -19 COLOR MONITOR W CHASSIS, WELLS-GARDNER -19 COLOR MONITOR 1 4-20 x 1-1 4 UNSLOTTED FIN. HEX HD. P.C. SUPPORT BRKT. -12 2 REQ'D. P.C. SUPPORT BRKT. - 6-1 2 2 REQ'D. 8x3 4 SLT. HEX HD. SCREW 10 REQ'D. 8-32 x 3 4 CARRIAGE BOLT 4 REQ'D.

Color Xy Monitor And G80 Circuit Description Startrek

Fri, 13 Apr 2012 21:58:52 GMT

To begin our discussion of the Color X-Y Monitor, let's first pay tribute to the other kind of monitor - the raster-scan. As you may remember from your knowledge of raster-scan displays like those in a TV , that the electron-beam inside the tube always moves in a predictable way. That is, it always starts at the top left of the screen and scans across it, forming a pattern of horizontal lines on the inside surface of the tube as it moves downward. When it gets to the bottom, the beam is forced...

Punkter Om Installation Time Crisis 2

Thu, 12 Apr 2012 22:13:49 GMT

Tand aldrig for strammen til maskinen for installering er fuldfort. For at undga mulige elektriske st0d sikres, at maskinen er forbundet til hovedstrammen med sikkert monterede jordstik. For at kunder ikke kommer til skade ved spillets bevagelser sikres, at der er mindst 50cm afstand til andre maskiner og vagge. For at undga skader pa maskinen p.g.a. fejlbetjening sikres, at sp ndingen pa hovedstrommen er 230 volt AC. BEMERK Hvis denne maskine placeres pa et poleret gulv, anbefales det at ligge...

Order By Part Number Only 1 Rallyx

Wed, 11 Apr 2012 19:43:14 GMT

UPPER DISPLAY PLEXI -17-15 16 x 5-3 4 x 3 16 194 WEDGE BASE LAMP 14V., 27A 5 REQ'D. 8 x 5 8 PHIL. TRS. HD. SCR. 3 REQ'D. TOP, 3 REQ'D. BOTTOM BLACK SPEAKER GRILL W 4-1-1 2 SCREWS 6 x 9 SPEAKER ASSY. W CABLE, 8 OHM, 7W. 8-32x 1-1 2 CARRIAGE BOLT 4 REQ'D. MAIN GLASS ASSY. -17-13 16 x 13-1 8 x 3 16 13 COLOR MONITOR DUALSYNC HORIZONTAL MTG. - ELECTROHOME GLASS CHANNEL-14-1 2 LG. 2 REQ'D. 8-32 x 1-1 4 CARRIAGE BOLT 3 REQ'D. SMALL RED SWITCH BUTTON W HARDWARE 2 REQ'D. 8-32 x 1-1 8 CARRIAGE BOLT 6...

Inspections Immediately After Transporting The Product To The Location Hotd3

Tue, 10 Apr 2012 18:54:33 GMT

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects cuts, etc. on the external surfaces of the cabinet Are Casters and Adjusters, damaged Do the power supply voltage and frequency...

Warning TotalCarnage

Tue, 10 Apr 2012 17:20:54 GMT

If a fluorescent tube drops and it breaks, it will implode Use care in handling. Switch OFF power to the game. Remove the marquee glass. Disconnect the fluorescent light assembly from its power cable. Remove the screws fastening the assembly to the cabinet and lift out the assembly. Switch OFF power to the game. Remove the steel speaker screen. Remove the baffle, taking care not to damage the speaker enclosure seals. The speakers pull out from the front of the cabinet. Be sure to disconnect the...

Kit Components Skins Game Conversion Kit

Mon, 09 Apr 2012 23:50:30 GMT

Unpack materials from carton and inspect for obvious signs of damage. Use this checklist to ensure the kit is complete. Some of these parts may already be installed. You must supply the remainder of the materials required for this conversion. Unpack materials from carton and inspect for obvious signs of damage. Use this checklist to ensure the kit is complete. Some of these parts may already be installed. You must supply the remainder of the materials required for this conversion.

midway games west inc 675 sycamore drive milpitas California 95035 httpwww midwaycom Gauntlet Dark Legacy

Mon, 09 Apr 2012 23:50:27 GMT

20-9620 4006-01003-04 4106-01001-10 4108-01193 1 OB 4308-01123-24B 4408-01128-00 4700-00012-00 5556-13956-00 5556-15272-00 KEY T20 TR-TX LONG ARM MS 6-32x1 4 P-PH-SEMS 4 SMS 6x5 8 P-PH 4 SMS 8x5 8 TRX 10 BLT 8-32x1-1 2 CB 16 NUT 8-32 KEPS 17 FW .172x.375x.036 17 FERRITE BEAD 2PC 1-1 4 SQ 3 FERRITE BEAD .375 IN. ID. 1 08-8067 CARDBOARD BEZEL BLACK UNIV 31-3581 SIGN P.O.P. DARK LEGACY 03-9663 SHIELD-ATTRACTION GAMES WEST REGISTRATION CARD MANUAL UNIV KIT LABEL FBI WARNING LABEL- EPILEPSY TEMPLATE...

TwoPlayer Game PrimalRage

Tue, 03 Apr 2012 17:41:58 GMT

Players battle each other in a match decided by winning two out of three rounds. A trophy and human followers are awarded to the player who wins each round, and a new territory on the globe is awarded to the winner of the match. Human followers are awarded for various accomplishments in the game. The number of followers awarded depends upon how well a player fights, including at tack combinations, damage to the opponent, use of finishing moves, and fatalities. If the two players are tied at the...

Order By Part Number Only Gorf

Sun, 01 Apr 2012 23:04:29 GMT

ACRYLIC HEADER - 22-3 8 x 7-7 16 x 3 16 GLASS CHANNEL-7-1 2 LG. 2 REQ'D. TOP HEADER BRKT. - 22-13 16 LG. BOTTOM HEADER BRKT. - 22-13 16 LG. 8x 5 8 PHIL. TRS. HD. S.M.S. 6 REQ'D. 8-32x 3 4 SLT. PAN HD. M.S. 4 REQ'D. REAR SCENERY BRKT. -8-3 8 LG. 2 REQ'D. 8 x 5 8 SLT. HEX HD. S.M.S. 8 REQ'D. DECORATIVE SIDE PANEL- RIGHT NOT SHOWN 22-5 16 x 20-7 8 x 1 8 GLASS EDGE CHANNEL-19-7 8 LG. 2 REQ'D. WEDGE BASE LAMP SOCKET 1532 6 REQ'JD. 8-32x 1-1 2 CARRIAGE BOLT 2 REQ'D. 8-32 x 1-1 16 CARRIAGE BOLT 6...

60 Color Service Generator for G07 Monitor Pacman 2

Sat, 31 Mar 2012 23:34:01 GMT

Electrohome has developed a color service generator that is specifically designed for use with the G07 color data monitor. It provides the monitor with both horizontal and vertical sync, as well as the following test patterns 2 Broad bar cross-hatch pattern Three color selection switches, red, green and blue, provide the ability to display the above patterns in the three primary colors as well as the three secondary colors. This product may be ordered from Contracts Marketing ELECTROHOME...

Cable Block Diagram MidwaySportstation

Sat, 31 Mar 2012 10:02:43 GMT

4. Open the player control panel and locate player panel cable H-22785. This cable connects to the joysticks, switches, fuses, and I-40 adapter. Connectors designated Player 1 mostly white wire colors and Player 2 violet mate with the same color cables from the main harness. Player 3 blue and Player 4 gray connectors mate with the same color cables from the main harness. Power connectors red and black from player panel fuses mate with the same color cable from the main harness. 5. Check wiring...

Table of Contents Centipede

Fri, 30 Mar 2012 22:42:04 GMT

1. Voltage Plug 2. Interlock and Power On Off D. Self-Test E. Option Switch 2. Coin Mechanism Multipliers 9 3. Examples of Game Price Settings 9 1. Attract 2. Ready-to-Play Mode 3. Play Mode 4. High Score initial Mode B. Fuse C. The Control Panel 1. LED Start-Switch 2. Leaf-Switch 3. Mini-Trak Ball Maintenance and Repair 19 D. Monitor E. Printed-Circuit Board 1. Game PCB 2. Regulator Audio II PCB F. Fluorescent Tube and Speaker Replacement 23 G. Game Illustrations and parts lists begin on page...

5 Accessories ConfidentialMission

Thu, 29 Mar 2012 02:25:51 GMT

When transporting the machine, make sure that the following parts are supplied. If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you. The Keys are inside the Coin Chute Door at the time of shipment from the factory. GD-ROM SERVICE MANUAL ENG 420-6620-01 1 INSTRUCTION MANUAL FOR THE GAME BOARD AND GD-ROM The Keys are...

Tools Required Rampart

Tue, 27 Mar 2012 17:06:10 GMT

Drill with a 1 2-inch and 5 l6-inch drill bits Socket wrench set and ratchet Color RGB monitor ' Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency 15.750 KHz Vertical frequency 60 Hz Video input IV to 3V peak-to-peak positive polarity 5 VDC 0.25V U 3.0 amps ' 12 VDC 1.0 amp -5 VDC 1.0 amp optional Insulated wire connectors if you are installing a new JAMMA harness 6 x l 2-Long, Type AB, Pan-Head, Snap-Action Switches 8 ji 10-24 x...

Function Labels Overlay Installation Gt3d

Tue, 27 Mar 2012 11:23:54 GMT

Line up the supplied function labels with the corresponding control panel holes. Remove the backing and carefully press into place. Be sure they are straight. Attach the HOOK SWING reference diagram above the trackball label. If your control panel is too narrow to fit the reference diagram, mount the diagram under the monitor glass on the bezel. Refer to the diagrams below. face left face right overlay overlay FUNCTION LABEL LAYOUT 1 NOTE TRACKBALL SHOULD BE CENTERED ON THE CONTROL PANEL...

Introduction Of The Owners Manual TitleFight

Mon, 26 Mar 2012 00:34:48 GMT

SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSIs, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative arid popular game machines to the world market. This Owner's Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation o electronic assemblies, eiectromechanicals, servicing control, spare parts, etc. as regards TITLE FIGHT, a new SEGA...

Safety Summary Assault

Wed, 21 Mar 2012 18:57:51 GMT

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply. Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should be only be plugged into a grounded three-wire outlet. If you have only a two-wire outlet, we recommend you hire...

How to Use this Manual Polepos

Wed, 21 Mar 2012 14:30:17 GMT

This manual, written for game operators and service technicians, describes the Pole Position game. The manual contains information about the Upright and Sit-Down Pole Position cabinets. Whenever information is unique to the Upright cabinet, this symbol appears Whenever information is unique to the Sit-Down cabinet, this symbol appears Wherever information is unique to Ireland-Built games, this symbol appears _ Chapter 1 describes new features, game setup, settings of option switches, self-test...

Product specifications Gauntlet Dark Legacy

Sun, 11 Mar 2012 04:26:53 GMT

Medium Resolution RGB or Standard Resolution RGB adjustable at U12 DIP switches Player Variables 1 to 4 Players Per Game Choice of Character Character Profile Memory Operator Variables Coinage, Game Options, Difficulty, Volume, Demo Mode, Audits, Statistics Automatic Power-Up Test Manual Multi-Level Menu System

Regulatoraudio Pcb Schema AsteroidsCaberat

Tue, 06 Mar 2012 23:17:53 GMT

The Regulator Audio PCB has the dual functions of regulating the 5 VDC logic power to the game PCB and amplifying the audio from the game PCB. The regulator consists of voltage regulator Q1, current source power transistor Q3 and Q3's bias transistor Q2. The regulator accurately regulates the logic power input to the game PCB by monitoring the voltage through high impedance inputs SENSE and -SENSE. The inputs are directly from the 5 VDC and ground inputs to the game PCB. Therefore, the...

Warning 1 Paperboy

Mon, 05 Mar 2012 03:22:38 GMT

To avoid possible electrical shock, turn off and unplug the game before performing any maintenance procedures. Perform the following procedure to remove replace the 1. Use a 1 8-inch hex driver to loosen the two screws securing the lower retainer to the cabinet. 2. Unlock and open the coin door on the front of the cabinet. 3. Carefully reach up through the coin door opening and release the spring-draw latches located under the control panel on both sides of the cabinet. 4. Use a 1 8-inch hex...

Installing the Foot Pedal Hydra

Thu, 01 Mar 2012 18:19:24 GMT

To install the foot pedal, you need a copy of the foot pedal installation template printed at the end of this chapter and the following parts from the kit Four fender washers and locknuts 1. Tape the foot pedal template to the lower right corner on the front of the game. Make sure the template is placed correctly as per the measurements printed on it. 2. Drill four 5 l6-inch corner holes and a 1 3 16-inch center hole through the template. 3. Feed the pedal harness through the large, 1 3 16-inch...

5 Accessories Initd

Tue, 28 Feb 2012 05:10:25 GMT

When transporting the machine, make sure that the following parts are supplied. Magnetic cards for the recording of play results, and cleaning kits for cleaning the head of the card reader writer are sold separately. Subsequent purchases of these items can be made by contacting the office listed on this Owner's Manual or the dealer from whom the product was originally purchased. Be sure to provide the part number s , name s , and required number of items. 601-11050 CLEANING CARD Package of 30...

Precautions Concerning The Place Of Installation LaserGhost

Fri, 24 Feb 2012 21:32:46 GMT

This is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage o Places subject to rain or water leakage, or condensation due to humidity, o In the proximity of an indoor swimming pool and or shower, o Places subject to direct sunlight. o Places subject to heat sources from heating units, etc., or hot air. o Vicinity of highly flammable volatile chemicals or hazardous matter, o Vicinity of anti-disaster...

Connecting Power Wires AtariGames

Fri, 24 Feb 2012 04:06:37 GMT

1. Connect the wires on the JAMMA harness to the wires for the power supply. You need 5V, -5V, and 12V for the Escape kit. This kit may not require all of the voltages used in your original game. Tie off any unused wires on the power supply. 2. You will notice that there is more than one wire for each voltage. You must use more than one wire, as called out in the footnotes of Table 1-2. Using more than one wire for each voltage ensures that you do not overload the edge connector and cause it to...

7 Precautions To Be Heeded When Moving The Machine ConfidentialMission

Wed, 22 Feb 2012 18:57:32 GMT

0 When moving the machine, be sure to unplug the power plug. Moving the machine with the plug as is inserted can damage the power cord, and cause fire and electric shock hazards. 0 When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords and earth wires. Damaging the power cords can cause electric shock and short circuit hazards. 0 When moving the...

Info Sav Alpine Racer 2

Tue, 21 Feb 2012 12:24:44 GMT

Dieses Dokument darf in keiner Weise vervielf ltigt werden. Jegliche Tonaufnahmen sowie die Speicherung auf Datentr ger Suchsysteme , die Weitergabe oder sonstiges Kopieren f r den gewerblichen und privaten Gebrauch sind untersagt und bed rfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED. Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED beh lt sich jedoch das Recht zu nderungen ohne vorherige Bekanntgabe vor. Dieses Ger t tr gt das...

2 Care In Operation Subroc 3d

Wed, 15 Feb 2012 23:40:05 GMT

o Are the IC boards and other connectors firmly connected oConnect ground wire as prescribed. Never connect to gas pipes, water pipes or electrical conduits o Arrange line cords and ground wires in the aisle so they will not be tripped over. o Always turn off the power supply switch before handling. o Avoid inserting and pulling the plug in rapid succession. oDo not check the IC board circuit with a tester. oCare should be taken t.o avoid dragging or dropping the machine when transporting it,...

Selftest BurgerTime

Wed, 15 Feb 2012 05:14:02 GMT

Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the game's speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and or service man to have the trouble fixed unless it is something you can do yourself such as replace a bad RAM or...

Warning Shuuz

Tue, 14 Feb 2012 18:12:18 GMT

To avoid electrical shock, unplug the cabinet while installing the kit. After installation. plug the game only into a grounded 3-wire outlet. Glass fieiainsr i 1782 148011 8 Foam Taoe 0479944 21 Bezel w ti Graphics i 178056-002.-t 2 W. x V16 I Thk Foam Tape i A0479824 Trak-8ail Adapter Harness Assy. 75-07002 F lai washer 75-99515 1 4 gt 20 NuV Washer Assy. A047441-01 JAMMA Powet J Supply Assy. 3A. 2S0V Fuss I A047365-01 SilUUZ PCS Assy, j 178265-001 t.-StyieNytonStarxloft 75-51488 i 10x3.0-...

Game Pcb 1 FastFreddie

Tue, 07 Feb 2012 19:41:08 GMT

Table 1-1 details game option switch settings on the game PCB. Options are preset at the factory and shown by the symbols. However, you may change the settings to suit your individual needs. To verify option switch settings, push reset button or power the game off and then on again. Set the self-test switch to on and verify the settings on the self-test screen. Then set the self-test switch to off. This table contains switch settings for options relating to game price, number of Fast Freddie...

C Z80 Control Logic DragonLair

Tue, 31 Jan 2012 08:31:45 GMT

This section describes the generation of three control inputs to the Z80 CLOCK , RESET-, and WAIT-. The control input Bus Request BUSRQ- may be wired on some boards, but it is never used. The Clock Circuit provides the Z80 Controller Board with a stable source of timing, thus insuring, among other things, that all audio sounds remain in tune. Composed of U24, U29, Yl, and other discrete parts, the Clock Circuit consists of an oscillator and several dividers and drivers. The oscillator is...

Rear View Pengo

Thu, 19 Jan 2012 07:30:50 GMT

ITEM NO. PART NO. QTY. REQ'D DESCRIPTION REF. DESG. Junction Box Metal Conn Quick Fem Fully .250 X .032 AWG 18-22 Conn Quick Fem Fully .187 X .020 AWG 18-22 Decal 2 Amp Fuse Switch SPDT Cherry Fuse 2 AMP 250V S.B. Holder Fuse Cord Line 3 Cond. ITEM NO. PART NO. QTY. REQ'D DESCRIPTION REF. DESG. 24 284-0007 1 Washer Flat Std O.D. l 4 25 283-0025 1 Nut Hex HD 10-24 Mach 26 282-0005 1 Bolt Carriage 10-24 27 310-0016 1 Insul TBG .187 ID 28 284-0004 2 Washer Flat Std O.D. 8 Button Plunger Yellow...

List of Illustrations TempestCocktail

Wed, 18 Jan 2012 00:39:31 GMT

Figure 3 International Voltage Plug Selection 4 Figure 4 Interlock and Power On Off Switches 5 Figure 6 Location of Self-Test Switch, Volume Control and Option Switches 7 Figure 8 Game Option Figure 9 Game Price Figure 10 Coin Counter Option Figure 11 Opening the Control Panel and Replacing Switches 20 Figure 12 Control Panel Wiring Figure 13 Encoder Wheel Maintenance and Repair 22 Figure 14 Video Display Figure 15 Printed-Circuit Board Removal 25 Figure 16 Speaker and Fan Figure 17 Power...

Aztarac Table Of Contents Aztarac

Mon, 16 Jan 2012 06:55:19 GMT

I. GENERAL INFORMATION PAGE NO. User Information Introduction Game Description Game Diagnostics Game Optional Switch Settings Installation amp Electrical Requirements ------------------------------14 110 220 VAC Conversion 110 220 VAC Interconnect Diagram 904-0006 Fig.l --------16 Routine Maintenace amp Service- Power Supply ----------------------17 Power Supply PSR-1105AP Troubleshooting Guide 18 Display PCB X-Y Monitor Adjustment Procedure 19 III. GAME PARTS DRAWINGS- PARTS LIST amp...

Starting Up HighImpact

Sun, 08 Jan 2012 06:20:25 GMT

Switch on power to the game. A rug pattern appears on the CRT screen. When the rug pattern ends, the screen shows CHECKING SCRATCH RAMS, and then CHECKING ROMS. The next screen shows SUPER HIGH IMPACT FOOTBALL REVISION LEVEL, CMOS TEST OK and the COIN SETTING. The game then moves to the Attract Mode. Insert the desired amount of coins or tokens. Select which player receives the credit by pressing the appropriate Player Start Button. Continue pressing the Player Start button until all credits...

2 Specifications Mr. Driller 2

Thu, 05 Jan 2012 20:42:04 GMT

Connected to JAMMA standard terminal 5V 5 2.5A or more and 12V 5 2.0A or more Temperature 0 C - 50 C, Humidity 10 - 85 no condensation Cabinets corresponding to JAMMA standard Direction of the monitor and the monitor signal Type of scanning retrace line Switchable to non-interlace interlace Horizontal synchronizing frequency 15.75kHz Vertical synchronizing frequency 60.0Hz 4-direction joystick 1x2 Button switch 1 x 2 Startswitch 1x2 Fix to the wooden install board of the cabinet 1 JAMMA...

To mount trackball to a wooden control panel without routing capability use Trackball Mounting Template 3 GT99

Wed, 04 Jan 2012 21:18:56 GMT

1. Fill any existing holes in the wooden control panel. 2. Place and secure Template 3 to your control panel in the desired location. NOTE The trackball should be as far away from the monitor as possible. 3. Carefully cut the hole for the trackball in the shape indicated on the template. The trackball should fit the hole shape exactly. 4. Drill the mounting holes as indicated. 5. Remove template and file down any rough edges. 6. Using the Trackball Orientation Template, cut a 3 hole in the...

Inspection Tron

Tue, 03 Jan 2012 13:30:09 GMT

1. Remove the game from its shipping crate. 2. Inspect the entire outside of it for any signs of damage. Any scratches Dents Cracks Any broken glass or plastic Just look it over closely and make a note of any signs of damage. 3. Remove the shipping cleats from the bottom of the cabinet. UPRIGHT MODELS ONLY In order to help prevent easy theft of your game, you may wish to remove the Caster Wheel Assemblies from the bottom of your cabinet at this time. 4. Install the four levelers, one at each...

Model No Tpp2up Model No Tpp2upus Popeye

Sat, 31 Dec 2011 16:52:15 GMT

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions manual, may cause interference to radio communications, It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area...

Introduction PrimalRage

Sat, 31 Dec 2011 15:49:48 GMT

Primal Rage is a head-to-head fighting game featuring state-of-the-art stop-motion animated characters. Players choose from seven different giant fantasy creatures in an attempt to dominate the new Urth, using fighting moves, powerful secret moves, masterful combo hits and graphic finishing sequences to eliminate their opponent. Primal Rage utilizes a proprietary new stop-motion animation technique that provides realistic and life-like character motion. In addition to state-of-the-art graphics,...

Install Electronics Tray Components MidwaySportstation

Wed, 28 Dec 2011 22:20:10 GMT

CAUTION Board set electronic components are static sensitive. Prepare an anti-static work area. Ground yourself before removing circuit boards from their protective shipping materials. WARNING Don't connect cables to the circuit boards or power supply when the power is on. Otherwise, you'll damage VGM electronics and void your warranty. CAUTION Hard disk drives are fragile. Don't stack or drop hard disk drives. NOTICE If your monitor requires positive sync, remove jumper J2 on the SIO Board. 1....

Wire The Circuit Boards MidwaySportstation

Wed, 28 Dec 2011 22:16:23 GMT

NOTICE You must install the Main JAMMA Wiring Harness supplied with this conversion kit. This VGM's 49-way joysticks require wires and circuits not found in earlier VGMs. If the connectors in your cabinet don't fit onto the CPU Board or wire colors don't match the JAMMA Chart, contact your authorized distributor for assistance. CAUTION Insulate unused wires within the JAMMA cable, especially red, yellow, orange and black power wires. Secure unused connectors away from the CPU Board and its...

A New Features Centipede

Fri, 23 Dec 2011 21:50:52 GMT

The Centipede game has several new parts. Even if you are familiar with Atari games, you should note these important differences. The new parts are Mini-Trak Ball Assembly. The widely used Trak Ball assembly has been redesigned. The basis for this compact, simplified design is a two-part molded plastic frame. Fewer parts in this control make servicing easier, and its very smooth action is designed for greater player accuracy. The circuitry has non-volatile memory for part of the high score...

Inspection NBAHangtime

Mon, 19 Dec 2011 22:56:25 GMT

Unpack the materials from the carton and inspect for obvious signs of damage. Use this checklist to be sure your kit is complete. 8 X 5 8 TAMPER RESISTANT SCREW

Tools Required Hydra

Mon, 19 Dec 2011 15:19:18 GMT

Drill with a 1 4-inch and 5 l6-inch drill bits, a 1 3 4-inch hole cutter or a 1 3 4-inch chassis punch , and a 1 3 l6-inch hole cutter 1 4-20 hex wrench Wire cutters and strippers Straight edge Squeegee X-ACTO knife Insulated wire connectors if you are installing a new JAMMA harness 5 32 Tamper-Proof Hex. Key Driver Red Square Boost Button With Lamp Packaging materials are not listed

Game Serial Number Location Battlezone 2

Sat, 10 Dec 2011 15:50:16 GMT

Your game's serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the TV monitor, Regulator Audio II PCB, Battlezone Analog Vector-Generator PCB, and Battle-zone Auxiliary PCB. Please mention this number whenever calling your distributor for service. BATTLEZONE ANALOG VECTOR-GENERATOR PCB BATTLEZONE ANALOG VECTOR-GENERATOR PCB

Service Manual Narc

Fri, 09 Dec 2011 06:32:25 GMT

WILLIAMS ELECTRONICS GAMES, INC. 340 I N. California Avenue Chicago, IL 60618 Programmed Chip Summary Continued on Inside-Back Cover CRAM Controller Local Ctlr Video RAM Ctlr GPU 8M J U2S CPU Board U78 CPU Board U79 A-5346-3036-1 A-5346-3036 -2 A-5346-3036-3 Address Decoder Image ROM Ctlr Video RAM Seq. A-b34' -3 3 -4 A-5346-3036-5 A-5346-3036-6 ROM Board 25 ROM Board U26 ROM Board U27 A-5343-3036-1 5 A-5343-3036-1 6 A-5343-3036-1 7 ft M Sonrd U2V ROM Board 29 ROM Board U30 ROM Board U31 ROM...

0410861 088068 111274 168587825 1694782 1699221 1610077 1610139 1610363 1610443 1644044101 209620 209727 20102091 20102092 20102093 20102095 2010383 31286313 312864 312865 3128681 312869 312870 312871 40060120904 40080103506 41060111508 41080119310b 43080 Blitz

Sun, 04 Dec 2011 05:12:28 GMT

Fan Assembly Blitz CPU Board Assembly Blitz 49-way Joystick Assembly Blitz Hard Disk Drive Assembly 49-way Joystick Cable Assembly 1 49-way Joystick Cable Assembly 2 Flexible Grommet .155 x .2 x 7 Blitz Perforated Electronics Cover Cable Tie 8 inch length Control Panel Cover Electronics Metal Mounting Plate Hard Disk Drive Shipping Container Wood Spacer for Joystick FBI Warning Label Registration Card Epilepsy Warning Label Electronic Device Caution Sheet FCC Canada Warning Label Program...

1988 by Atari Games Corporation Toobin

Sat, 03 Dec 2011 22:33:57 GMT

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976, This Act provides for substantial penalties...

Warning NBAJam

Fri, 02 Dec 2011 19:01:08 GMT

If a fluorescent tube drops and it breaks, it will implode Use care in handling. Remove Fluorescent Light Assembly Switch OFF power to the game. Remove the marquee glass above . Disconnect the fluorescent light assembly from its power cable. Remove the screws fastening the assembly to the cabinet and lift out the assembly. Switch OFF power to the game. Remove the tamper resistant screws from the steel speaker screen. Remove the baffle, taking care not to damage the speaker enclosure seals. The...

Selftest SatansHollow

Thu, 01 Dec 2011 06:57:01 GMT

A slide switch is provided to make the game run a Self-Test on itself. The SELF-TEST SWITCH is located just inside the cabinet on the right side of the coin door frame as you face it. To put the game into the Self-Test mode turn the game ON and let it warm up for a few minutes. Then slide the SELF-TEST SWITCH to the ON position and actuate the TILT switch on the back side of the coin door just below the door lock to obtain the Self-Test-Menue display on the monitor screen. When in the Self-Test...

Sicherheitshinweise Gun Survivor 2

Mon, 28 Nov 2011 13:17:35 GMT

Um einen ordnungsgem en Betrieb dieses Ger tes zu gew hrleisten, mu vor Aufstellung, Inbetriebnahme und Gebrauch das Handbuch sorgf ltig gelesen werden. Sobald der Besitzer dieses Ger tes die Demontage, Aufstellung, Inbetriebnahme oder den Service einer anderen Person bertr gt, mu er sicherstellen, da diese Person vor Arbeitsbeginn die n tigen Sicherheitshinweise und die dazugeh rigen Kapitel des Handbuches liest und versteht. Um jegliche Unf lle w hrend des Betriebes zu vermeiden, m ssen obige...

Operation Maintenance and Service Manual Battlezone 2

Sun, 27 Nov 2011 22:08:17 GMT

Complete with Illustrated Parts Lists Copyright 1980 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

If a dollar bill validator is desired the Mars upstacker AE2411 is recommended Mortal Kombat 4

Fri, 18 Nov 2011 14:37:55 GMT

The information in this manual is current at time of its release. Fill out and mail in the game Registration card. Be sure to include the game serial number. For your records, write the game serial in the manual. MIDWAY Games Inc. reserves the rights to make modifications and improvements to its products. The specifications and parts identified in this manual are subject to change without notice. Section One - Operation and Troubleshooting Safety Set-up Inspection and Location Cabinet Assembly...

Cabinet Modifications Blitz

Tue, 15 Nov 2011 13:25:31 GMT

1. Verify the operation of the existing game before making any changes to the cabinet. Pay special attention to those components that will be used again after conversion is completed Power Supply, Video Monitor, Currency Acceptors, Wiring Harnesses, Cabinet Locks, Lighted Marquee, etc. . 2. Switch off power to the game. Disconnect the line cord from the A.C. power. Clear the work area. Cover or protect the non-wood items marquee, monitor, coin door, brackets, line cord, etc. . 3. For cabinets...

Operator Panel Zaxxon

Wed, 09 Nov 2011 08:43:34 GMT

ZAXXON is a microprocessor based, digital-integrated circuit computer video game. The heart of the computer is the CPU U24 , a Z80A located on the 834-0214 Assy IC Board A. The Alpha type chip MUST ALWAYS be used, as the Z80 is not fast enough to run the programs. Master timing is crystal-driven at 48.66 MHz, XI, Zone 6-D, Sht. 7, Assy. IC Bd. B, 834-0211 through Ql, Q2, Tl, U19, U38, U41, and frequency dividers Ul, U2, and U21. CPU timing 1H is taken from U1 p-14, through U45, U9, applied to...

Selftest SuperPacman

Sun, 06 Nov 2011 07:33:58 GMT

Slide switches are provided to make the game run a Self-T st on itself. The SELF-TEST SWITCHES are located on a mounting bracket on the inside left hahd side of the coin door. When in the Self-Test mode, the monitor screen will display the results of certain test functions it has run on itself. These will be discussed in more detail later. The control panel is held in place by three latches, one on the left side, one on the right side, and one in the center of the front of the cabinet. They are...

Asteroids Wiring Diagram 03515602 A AsteroidsCaberat

Sat, 05 Nov 2011 07:38:02 GMT

lt XUiPf gt D W T C90Q-2-XX . COIN amp QO amp . cos V 30K Q AG-tAM O'ZOVOt-O AND ZO'A ZR AZAPTEfit. HAH HE S3 ASSY. v V lt S DdAf '- A. 035-2,I9-Of LEFT COiU SW ItJ.O.' CevOTtR. COIM SVJ KI.O.1 Right coiu sw in.o. TEiiT WlTcM SLAM SWITCH LEFT coihl LOCKOUT .OIL. CEUTER, COIN LOCKOUT COIL KlSHT COIN UJCKOOT JDIl_ NOT USED MOT USEDl

Tlx 9103351621 Pengo

Mon, 31 Oct 2011 23:50:34 GMT

Copyright 1982 by SEGA Electronics, Inc., All Rights Reserved Introduction 1 Important Notes 2 Game Concept 3 Scor i 5 Option Selection 6 Circuit Description 8 Sel t-Test . 10 Troubleshooting Tips 11 Troubleshooting Diagrams 12 Parts Catalog 15 Cabinet Wiring Diagram 109 PENGO is a microprocessor based coin-operated electronic game, that makes extensive use of digital integrated circuitry and television monitor concepts. This manual is designed for the use of maintenance technicians who possess...

Location Of Casters And Leg Levelers Under Cabinet And Seat Gauntleg

Sun, 30 Oct 2011 03:04:30 GMT

4. This game is intended for use only in a fixed position. Ensure that the final adjustment raises the game so that the caster wheels are not touching the floor. Distribute weight equally on each 5. Place the box containing the control panel on the floor with its underside up. Open the container carefully and remove the packing material. Inspect the control panel for any signs of damage. 6. Lift the control panel assembly from its box and set it on its front side. Remove the wing nuts from the...

Section 1 Operation and Troubleshooting MortalKombat

Sun, 30 Oct 2011 02:28:18 GMT

Converting from a STREET FIGHTER II game Suggested Control Panel PC Board Converting from a typical video game Suggested Template Suggested Control Panel Installing PC Boards into a JAMMA Installing PC Boards into a Non-JAMMA Player Typical Control Control Control Switch Location Main Diagnostic Switch DIP Switch Test amp CPU amp Sound Monitor Burn-in Coin Game Game Standard Pricing Custom Pricing CPU Board CPU Board Sound Board Sound Board JAMMA Chart And interboard Cabinet Coin Meter Sound...

Player Panel Template 1610830 MidwaySportstation

Mon, 24 Oct 2011 00:31:16 GMT

1. If you're assembling both kit 15909 and optional player panel 45494, skip to Step 19. If you're assembling just kit 15909, proceed with the next step. 2. Locate and unfold the player panel template. Temporarily stack newspapers, books, magazines, etc., on the template. The weight will flatten the template sufficiently for use. 3. If necessary, remove buttons, joysticks and T-nuts from the old player panel and cabinet front. Remove the panel covering and artwork from the previous game....

Eimom RoadRiot

Thu, 20 Oct 2011 00:40:48 GMT

Atari Games Ireland Limited European Customer Service Office TipperaryTown, Ireland Fax 062-51702 Telex 70665 lt 0 062-52155 Monday-Friday, 9 00 a.m. 5 30 p.m. GMD N o T ICE R i . N O N - A T A R I Par r s Copyright 1991 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for...

Diagram Trackball GT97

Fri, 07 Oct 2011 11:10:01 GMT

Installing the trackball as far away from the monitor as possible will prevent players hands from hitting the monitor glass when rolling the trackball forward. TRACKBALL MUST 8E CENTERED ON THE CONTROL PANEL When moking the hole for the trackball, follow the instructions, starting on the right, for the type of control panel you will be using. When installing the trackball, make sure the trackball is in the right orientation. Refer to picture below. Poirtior I ha ir c lt bali as l r Awaf Votn ih...

Fri, 30 Sep 2011 12:33:16 GMT

NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. FOR PERMISSION REQUESTS, WRITE MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 II. Location and Inspection Installation Game Volume Adjustment Option Switch III. Game Self-Test Attract Ready to Play Play Two Player IV....

PINBALL Continental US 18003233555 Tapper

Tue, 27 Sep 2011 21:10:09 GMT

JMPMMy ' gt Q60 gt Weil Belmont Avenue Franklin Pailt IWnO't, 60131 phone 312 451-9200 ' COPYRIGHT MCMLXXXIV BY BALLY MIDWAY MFG. CO. ALL RIGHTS RESERVED NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION...

Section One NBAJam

Mon, 19 Sep 2011 14:28:57 GMT

The following safety instructions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page before preparing your game for play. AC POWER CONNECTION. Before connecting the game to the AC power source, verify that the line voltage selection chart jumper wires are installed correctly for the line voltage in your area. For details, refer to Section 3. PROPERLY GROUND THE GAME. To...

Return Merchandise Authorization GT97

Sun, 18 Sep 2011 14:31:29 GMT

All returned merchandise must have a Return Merchandise Authorization RAM number marked clearly on the outside of the package. You must obtain all RAM numbers from your authorized Incredible Technologies, Inc. distributor. Please have your Incredible Technologies, Inc. serial number available when calling for an RMA number. Merchandise returned without an RMA number will not be accepted. Advance replacement boards will be shipped to distributors or, at the distributor's request, will be...

Converting A Typical Video Game Cabinet Prepare The Cabinet MidwaySportstation

Thu, 15 Sep 2011 15:15:43 GMT

1. Verify operation of the old VGM before making changes to the cabinet. Pay special attention to components that you will reuse. Power supply, video monitor, currency acceptors, wiring harnesses, cabinet locks, lighted marquee, etc. 2. Switch off power to the VGM. Disconnect the line cord from the AC power. Clear the work area. Cover or protect non-wood items. Marquee, monitor, coin door, brackets, line cord, etc. 3. Remove old decals and artwork from the cabinet sides. Clean off glue...

Game Serial Number Location TempestCocktail

Thu, 15 Sep 2011 15:01:34 GMT

Your game's serial number is stamped on a label on the outside of 'r-.t game. The same number is also stamped on the chassis of the video display, Regulator -Audio II PCB, and the Tempest Analog Vector-Generator PCB and Auxiliary PCB. Please mention this number whenever calling your distributor for service. Operation, Maintenance and Service Manual Complete with Illustrated Parts Lists Copyright 1981 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any...

Operators Manual VictoryLap

Fri, 09 Sep 2011 19:14:38 GMT

It is the responsibility of the operator to maintain customer safety at ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL 1996 NAMCO LIMITED. all rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for public or private use, without permission from

www midway com MidwaySportstation

Fri, 09 Sep 2011 00:35:43 GMT

Dual Product with Player-Selectable Games 1-Assembly 2-Operation 3-NFL Audits 4-NBA Audits 5-Wiring 6

Rom Summary TurkeyShoot

Sat, 03 Sep 2011 07:24:56 GMT

CPU-BOARD JUMPERS W1, W3, W6, W8, W10, W11, W14 and W16. Remove jumper W11 for cocktail games. TURKEY SHOOT is a trademark of WILLIAMS ELECTRONICS, INC. 1984 WILLIAMS ELECTRONICS, INC. TO ORDER REPLACEMENT ROMS from your authorized WILLIAMS distributor, specify 1 part number shown above, 2 ROM-label color, 3 REV level number on the label, and 4 which game the ROM is used in. schematic and logic diagrams

Xybots Coin Information and Game Statistics Sheet Xybots

Sun, 28 Aug 2011 22:21:11 GMT

Figure 1-1 Control and Switch Figure 2-1 RAM Test Figure 2-2 ROM Test Figure 2-3 Switch Figure 2-4 Coin Figure 2-5 Game Figure Figure Figure 2-8 Playfleld Test Figure 2-9 Motion Object Figure 2-10 Alphanumerics Figure 2-11 Color Figure 2-12 Color Purity Test Figure 2-13 Convergence Test Figure 2-14 Sound Figure 3-1 Leaf Switch and Joystick Figure 3-2 Joystick Disassembly and Lubrication Figure 3-3 Control Panel, Video Display, and Speaker Removal 3-7 Figure 4-1 Removing IC Cut-Pin Method Figure...

Table of Contents CongoBongo

Sun, 28 Aug 2011 20:32:11 GMT

Introduction 1 Important Notes 2 Game Scoring 4 Option Selection 5 Theory of Operation 7 Parts Catalog 20 700-0134 Top Assembly 21 Ground Plane Assembly 28 Volume Control Block Assembly 30 Game Interface Board Assembly 34 700-0137 T-8 Cocktail Top Assembly 36 T-8 Cabinet Accessory Assembly 40 Control Panel Assembly 43 8-Way Joystick Assembly 45 Power Supply Assembly 47 Regulator Unit 49 Nanao 700-0138 Top Assembly 65 700-0139 Top Assembly 72 Component Shelf Assembly 79 Operator Control Block...

Operators Manual PropCycle

Wed, 24 Aug 2011 02:44:37 GMT

It is the responsibility of the operator to maintain customer SAFETY AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY, 1996 NAMCO LIMITED. all rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for public or private use, without permission from NAMCO EUROPE LIMITED...

A Setup M.A.C.H. 3

Tue, 23 Aug 2011 09:20:09 GMT

1. Unstrap the video disc player from the seat of the player compartment on the SIT-DOWN game or from the main shipping box on the UP-RIGHT game. 2. Open the video disc player box and remove the player by lifting from the front and rear of the unit. Place all cables and the remote control unit in the box and store for future use. These accessories are not used with this game. 3. With the back door open, place the video disc player on the floor in front of the rear cabinet opening with the front...

Table Of Contents Lazarian

Sun, 21 Aug 2011 20:24:37 GMT

Installation Game Volume Adjustment Option Switch Calibration Mode Attract Ready to Play Play r Two Player Cleaning Fuse Replacement Opening the Control Panel Removal of the Main Display Glass amp T.V. Bezel T.V. Monitor Printed Circuit Board Opening the Attraction No. 636 Lazarian Upright Header Fluorescent Fixture Assy 5-1 No. 636 Lazarian Upright Header Fluorescent Fixture Assy. Parts List 5-1 No. 636 Lazarian Upright No. 636 Lazarian Upright Front Parts No. 636 Lazarian Upright Rear No. 636...

Atari PrimalRage

Fri, 19 Aug 2011 16:54:47 GMT

Patents are pending on several parts nf the Primal Rage pnn How to Use This Manual 1-1 Operating the Game 1-2 Inspecting the Game 1-2 Control and Switch Locations 1-2 Power On Off Switch 1-2 Volume Control 1-2 Self-Test Switch 1-2 Coin Counter 1-2 Video Display Controls 1-3 Setting the Coin and Game Options 1-3 Game Play 1-3 1-3 Game Play 1-3 One-Player Game 1-3 Two-Player Game 1-4 Hidden Features 1-4 Entering and Exiting the Self-Test 2-2 Select Test Menu 2-2 Adjust Statistics Screen 2-3 More...

Table Of Contents BurgerTime

Wed, 17 Aug 2011 16:44:02 GMT

I. Introduction Installation Game Volume Adjustment Option Switch Self-Test Attract Ready to Play Play High Score Initial Two Player Cleaning Fuse Replacement Opening the Control Panel Removal of the Main Display Glass amp T.V. T.V. Monitor Printed Circuit Board Opening the Attraction No. 333 Burger Time Upright Front No. 333 Burger Time Upright Front Parts No. 333 Burger Time Upright Rear No. 333 Burger Time Upright Rear Access Parts List 5-5 No. 334 Burger Time Cocktail No. 334 Burger Time...

Product Specifications MidwaySportstation

Tue, 16 Aug 2011 17:06:34 GMT

Equipment Characteristics Video Display Monitor Standard or medium resolution, RGB Composite, positive or negative sync DIP switch U12-2 sets resolution SIO Jumper J2 sets sync polarity VGM Characteristics Player Variables Parental Advisory Disclosure Suitable for all Ages NOTICE FCC COMPLIANCE. Installation of this kit into any existing product does not guarantee compliance with FCC requirements. You are solely responsible for FCC compliance for installations in other products. You must remove...

Upright Typecockpit Typ Subroc 3d

Mon, 15 Aug 2011 23:01:45 GMT

Copyright 0 1982 by Sega Enterprises, Ltd. o For prevention of illegal production and conversion of our machines, a seal showing ORIGINAL SEAL is pasted on each of the machines produced by SEGA, or a LICENCE SEAL is attached to each IC Board and other kits to be issued by SEGA for production of SEGA machines. o This is to prevent illegal acts to produce copies of machines and IC Boards without our consent or to produce, convert, or sell machines or IC Boards, and to operate such copies or...

Midway Mfg Co Rallyx

Wed, 10 Aug 2011 22:46:32 GMT

A BALLY COMPANY. . ' ' 10750 WEST GRAND AVENUE f FRANKLIN PARK, ILLINOIS 60131 , RHONE 1312 451-1360 CABLE ADDRESS MlDCO TELEX NO. 72-1596 M NOj 093 amp -t 03QQ 0000 _____,_________ .'. .' ' '' .'.- . . _ GENERAL INSTRUCTIONS FOR RALLY-X UPRIGHT 1. Remove shipping cleats located on bottom of cabinet. 2. Install four 4 provided leg levelers to bottom of cabinet and level cabinet. 3. The power is controlled by a switch located on top of the cabinet. Additional taps have been provided on the...

Safety Warning CyberCycle

Mon, 08 Aug 2011 14:09:31 GMT

In order to use this machine safely, be sure to read this Operators Manual carefully before installation and use of the machine. Whenever the owner of this machine entrusts disassembly, installation, adjustment, routine maintenance or trouble shooting to another person, the owner should ensure that they read the appropriate precautions and relevant sections of this manual before starting work. In order that no accidents occur when the machine is in operation, strictly follow the notes on safety...

A CAUTION CHECK POWER SUPPLY LINE VOLTAGE SELECTOR SWITCH Set the Nbanfl

Thu, 04 Aug 2011 01:11:15 GMT

110 220 VAC selector on the power supply for the correct local line voltage. Check the selector setting before switching on the game. 10. Reinstall the rear door and close it. Lock the rear door and remove the key. If required, install the extra padlock through the hasp. Install the screws at the top and sides of the rear door. Tighten the screws snugly. Close and lock the cash box and coin doors. NOTICE For additional security, the factory provides tamper-resistant screws and a matching wrench...

table of contents AstroBlaster

Wed, 27 Jul 2011 13:59:57 GMT

Game Game Set-Up and Inspection 5 G-80 Theory of Maintenance Game Parts Catalog. . . . Schematics. Astro Blaster is an electronic game that makes extensive use of digital integrated circuitry and television monitor concepts. This manual is designed for the maintenance technician who possesses a general knowledge of solid state circuitry, microprocessor and digital integrated circuitry, and TV monitor concepts. Any individual not knowledgeable in these areas should not attempt repair of the...