Selftest
Slide switches are provided to make the game run a "Self-Tçst" on itself. The SELF-TEST SWITCHES are located on a mounting bracket on the inside left hahd side of the coin door.
When in the Self-Test mode, the monitor screen will display the results of certain test functions it has run on itself. (These will be discussed in more detail later.)
TO SERVICE THE CONTROL PANEL(S)
1. UPRIGHT MODEL:
° The control panel is held in place by three latches, one on the left side, one on the right side, and one in the center of the front of the cabinet.
They are spring loaded to provide constant positive pressure on their latch plates.
They can be reached through the coin door AFTER turning power to the game off.
To release the latches, lift up and toward the center of the control panel.
Once they are released, unhook them from their latch plates.
° To remove the control panel:
Raise it up and tilt it toward you until you can see the cable behind it.
Cradling the control panel between yourself and thé cabinet, disconnect it from its cabling and nylon retaining strap.
The control panel is now free and can be removed.
° To reinstall the control panel(s), reverse this procedure.
2. COCKTAIL TABLE MODEL:
° Each control panel is held in place by several screws, two on the inside of the cabinet and three along the bottom edge of the control panel.
Turn the power off to the game.
Open the coin box door and release the two latches on the inside of the cabinet up next to the table top.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!!
Once they're released, unhook them from their latch plates.
Grasp the table top in the center above the coin door lifting up and to the side to tilt it open.
CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.
Remove the screws which secure the control panel in place. ° To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed. 0 To reinstall the control panel(s), reverse this procedure.
REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY
1. UPRIGHT MODEL:
NOTE: In order to do this, the control panel MUST be removed first. See the "UPRIGHT MODEL" procedure.
° Turn the power to the game off and remove the control panel. This frees the main-dis-play-glass so it can be lifted up.
° By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out.
0 Loosen the screws which secure the T.V. bezel-glass-clamps in place.
Move the clamps to the side and the bezel glass may be removed.
Remove the above mentioned'screws and the bezel with four bezel-glass-clamps may be removed.
0 To reinstall the T.V. bezel asssembly and the main-display-glass, reverse this procedure.
2. COCKTAIL TABLE MODEL:
NOTE: This may be done with the table top in the open or the closed position. If you decide to open the table top, TURN THE POiER TO THE GAME OFF FIRST.
e Remove the screws which secure the table top glass clamps in place. ° Remove the table top glass.
° Loosen the screws which secure the T.V. bezel-glass-clamps in place. Move the clamps to the side and the bezel glass may be removed.
Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed.
° To reinstall the T.V. bezel assembly and the table top glass, reverse this procedure. VOLUME CONTROL POT
The volume control pot is located on the C.P.U. board. The other board is the Video board. There is only one pot. For adjustment, it may be reached through the rear access door on the UPRIGHT models. On the COCKTAIL TABLE models, you will have to open the table top to reach it.
To make the sounds louder, turn the pot clockwise as you face it ).
To make the sounds less loud, turn the pot counterclockwise as you face it (f*
Post a comment